Tannoy CMS601BM
Producator: Tannoy3% reducere pentru contactele prin clubafaceri.ro
Prezentare Tannoy CMS601BM
The CMS601 is equipped with a low insertion loss 60W line transformer easily configurable to the following settings via front baffle mounted rotary tapping switch:
70V systems: 60W / 30W / 15W / 7.5W / OFF & low Impedance operation
100V systems: 60W / 30W / 15W / OFF & low Impedance operation
Two CMS601 model versions and a separate back can are available to satisfy the vast majority of installation application requirements:
CMS601 BM (Blind Mount) - supplied with an integral back can.
CMS601 PI (Pre-Install) - supplied without a back can.
CMS601 PI Back Can (Pre-wire back can) - use with the CMS601 PI.
The zinc plated steel back cans have an integrated, recessed termination box. The removable locking connector has screw terminals for secure wire termination and \\\\\\\\\\\\\\"loop through\\\\\\\\\\\\\\" facility. Strain relief is provided by a clamping mechanism for use with plenum rated cable or conduit.
SYSTEM
Frequency Response (-3dB) (1) BM Back can 78Hz - 22kHz
Frequency Range (-10dB) (1) BM Back can 51Hz - 24kHz
Frequency Range (-10dB) (1) PI Back can 46Hz - 24kHz
System Sensitivity (1W @1m) (2) 91dB (1W = 2.45V for 6 Ohms)
Nominal Coverage Angle 90 degrees conical
Coverage Angle (1kHz to 6kHz) 92 degrees
Directivity Factor (Q) 7.1 averaged 1kHz to 6kHz
Directivity Index (DI) 7.9 averaged 1kHz to 6kHz
Rated Maximum SPL Average: 108dB
Peak: 112dB
Power Handling (3) Average: 60W
Programme: 120W
Peak: 240W
Recommended Amplifier Power 120W @ 6 Ohms
Nominal Impedance 6 Ohms
Transformer Taps (via front rotary switch) 70V: 60W / 30W / 15W / 7.5W/OFF
& low impedance operation
100V: 60W / 30W / 15W / OFF
& low impedance operation
Crossover 7kHz inductively coupled
TRANSDUCERS
Low Frequency 1 x 165mm (6.50\\\\\\") mineral loaded
polypropylene ICT
High Frequency 1 x ICT aluminium dome
PHYSICAL
Enclosure Back Can: Zinc plated steel
Baffle: Reflex loaded UL 94V-0 rated ABS Grille: Steel, with weather resistant coating
Safety Features Safety ring located at rear of enclosure
for load bearing safety bond
Clamping Design Min / Max Clamping Range: 8.0mm (0.32\\\\\\") / 29.0mm (1.14\\\\\\")
Recommended Clamp Torque: 1.5Nm
Back Can Options Blind Mount (BM): Complete with fixed back can
Pre Install (PI): Separate back can for pre installation
Cable Entry Options Cable clamp & squeeze connector for
conduit up to 22mm
Conduit Knockouts 3 Sets of horizontal positions: 19 / 22 / 28mm (0.75 / 0.87 / 1.10)
Connectors Removable locking connector with screw
terminals with \\\\\\"loop through\\\\\\" facility
Safety Agency Ratings (pending) UL-1480, UL-2043, CE
BM Hole Cutout Diameter 253mm (9.96\\\\\\")
PI Hole Cutout Diameter 253mm (9.96\\\\\\")
Dimensions
Bezel diameter: 280mm (11.02\\\\\\")
BM model: Front of ceiling to rear of back can 258mm (10.16\\\\\\")
BM model: Front of ceiling to top of safety loop 275.30mm (10.84\\\\\\")
PI model: Front of ceiling surface to rear of speaker unit 95.50mm (3.76\\\\\\")
PI model: Front of accessory back can bezel to top of safety loop 168.50mm (6.60\\\\\\")
Net Weight (ea) CMS601 BM: 6.50kg (14.33lbs)
CMS601 PI: 4.00kg (8.82lbs)
PI back can: 3.685kg (8.06lbs)
Included Accessories C Ring
Tile bridge
Paint mask
Cutout template
Grille
Optional Accessories Plaster (mud) ring
S********************
va rugam sa va autentificati accesand urmatorul buton: